You are logged in as erlich
Question 1:
Why would you use the command IPX maximum-paths?
A. To define the maximum hops
B. To specify the number of routes available
C. To provide load sharing
D. To increase the tick count
Question 2:
What type of protocol is IPX?
A. Connection-oriented
B. Connectionless
C. Nonroutable
D. Connection like
Question 3:
What do NetWare clients use to find NetWare servers?
A. GNS packets
B. SAP packets
C. RIP packets
D. SPX packets
Question 4:
Which of the following commands enables IPX routing?
A. ipx maximum-paths
B. ipx routing
C. ipx network
D. router novell-rip
Question 5:
Which command is used to display IPX routing tables?
A. show ipx servers
B. show ipx route
C. show ipx traffic
D. show ipx interface
Question 6:
What is the default WAN tick metric for IPX networks?
A. Five
B. Six
C. Seven
D. Eight
Question 7:
When using multiple encapsulations on an interface, what must be assigned?
A. Multiple protocols
B. Multiple network numbers
C. Multiple subnet masks
D. Multiple SAP types
Question 8:
Which metrics does Novell RIP use?
A. Bandwidth and delay
B. Ticks and hop count
C. Distance and cost
D. Size and throughput
Question 9:
How do you obtain an IPX network address?
A. Apply to InterNIC
B. Use DHCP
C. Add the address with the subnet mask
D. Obtain it from the network administrator
Question 10:
When configuring interfaces for IPX, what must be assigned to each interface?
A. IP address
B. Host address
C. Network number
D. Subnet mask
Question 11:
Which of the following occurs when a router running Novell RIP has two equal paths to a network?
A. Selects the route with the lowest hop count.
B. Discards the packet.
C. Forwards the packet out the default route.
D. Implements load sharing.
Question 12:
Where does the response to a GNS request come from if there is both a Cisco router and a NetWare server on the same LAN?
A. Router
B. Local NetWare server
C. Local SAP server
D. Switch
Question 13:
Select the command that you would use to check IPX routing updates.
A. show ipx routing updates
B. show ipx routing activity
C. debug ipx routing activity
D. debug ipx rip
Question 14:
Which IPX routing command is used to show the number and type of packets received and transmitted by the router?
A. show ipx servers
B. show ipx route
C. show ipx traffic
D. show ipx interface
Question 15:
Which configuration command is used to set the number of routes used for load sharing?
A. ipx routing
B. ipx networks
C. ipx maximum-paths
D. router rip
Question 16:
Which frame types are compatible with the Cisco IOS name Novell-ether?
A. Ethernet_II
B. Ethernet_802.2
C. Ethernet_SNAP
D. Ethernet_802.3
Question 17:
What does IPX use in the host portion of an address to eliminate the use of ARP requests?
A. SAP
B. SPX
C. MAC
D. RARPs
Question 18:
Where are SAP tables stored?
A. On workstations and servers
B. On routers and servers
C. On routers and workstations
D. On routers only
Question 19:
What is the encapsulation type on a router for a Novell network running version 3.12?
A. Novell-ether
B. ARPA
C. SNAP
D. SAP
Question 20:
What is the default type of routing protocol used by Novell NetWare?
A. Link-state
B. Distance vector
C. Hybrid
D. OSPF
Question 21:
Which Cisco IOS command is used to check IPX SAP updates?
A. show sap routing updates
B. show sap routing activity
C. debug ipx sap activity
D. debug sap routing activity
Question 22:
What is correct regarding the node number using Novell's IPX addressing scheme?
A. 80 bits long
B. Written in decimal
C. Same as the MAC address
D. Number assigned by an administrator
Question 23:
What do routers do with SAP packets?
A. Build a SAP table
B. Discard the SAP packets
C. Forward the SAP packets
D. Send them to a SAP server
