Chapter 7 Exam
Question 1:
What do NetWare clients use to find NetWare
servers?
A. GNS
packets
B. SAP
packets
C. RIP
packets
D. SPX
packets
Question 2:
Which frame types are compatible with the Cisco
IOS name Novell-ether?
A.
Ethernet_II
B. Ethernet_802.2
C.
Ethernet_SNAP
D.
Ethernet_802.3
Question 3:
Which command is used to display IPX routing
tables?
A. show ipx
servers
B. show ipx
route
C. show ipx
traffic
D. show ipx
interface
Question 4:
What type of protocol is IPX?
A.
Connection-oriented
B.
Connectionless
C.
Nonroutable
D. Connection
like
Question 5:
Which IPX routing command is used to show the
number and type of packets received and transmitted by the router?
A. show ipx
servers
B. show ipx
route
C. show ipx
traffic
D. show ipx
interface
Question 6:
Which of the following occurs when a router
running Novell RIP has two equal paths to a network?
A. Selects
the route with the lowest hop count.
B. Discards
the packet.
C. Forwards
the packet out the default route.
D. Implements
load sharing.
Question 7:
Where are SAP tables stored?
A. On
workstations and servers
B. On routers
and servers
C. On routers
and workstations
D. On routers
only
Question 8:
When configuring interfaces for IPX, what must
be assigned to each interface?
A. IP address
B. Host
address
C. Network
number
D. Subnet
mask
Question 9:
What do routers do with SAP packets?
A. Build a
SAP table
B. Discard
the SAP packets
C. Forward
the SAP packets
D. Send them
to a SAP server
Question 10:
Select the command that you would use to check
IPX routing updates.
A. show ipx
routing updates
B. show ipx
routing activity
C. debug ipx
routing activity
D. debug ipx
rip
Question 11:
Which configuration command is used to set the
number of routes used for load sharing?
A. ipx
routing
B. ipx
networks
C. ipx
maximum-paths
D. router rip
Question 12:
What is not
a valid Cisco IPX Ethernet encapsulation type?
A. ARPA
B.
Novell-ether
C. SNAP
D. 802.3
Question 13:
Which of the following is NOT a part of the Novell IPX Protocol Suite?
A. Service
Advertising Protocol (SAP)
B. Network
Core Protocol (NCP)
C.
Transmission Control Protocol (TCP)
D. Sequence
Packet Exchange (SPX)
Question 14:
Why would you use the command IPX maximum-paths?
A. To define
the maximum hops
B. To specify
the number of routes available
C. To provide
load sharing
D. To
increase the tick count
Question 15:
How do you obtain an IPX network address?
A. Apply to
InterNIC
B. Use DHCP
C. Add the
address with the subnet mask
D. Obtain it
from the network administrator
Question 16:
What is correct regarding the node number using
Novell's IPX addressing scheme?
A. 80 bits
long
B. Written in
decimal
C. Same as
the MAC address
D. Number
assigned by an administrator
Question 17:
When using multiple encapsulations on an
interface, what must be assigned?
A. Multiple
protocols
B. Multiple
network numbers
C. Multiple
subnet masks
D. Multiple
SAP types
Question 18:
What is the default WAN tick metric for IPX
networks?
A. Five
B. Six
C. Seven
D. Eight
Question 19:
Which of the following commands enables IPX routing?
A. ipx
maximum-paths
B. ipx
routing
C. ipx
network
D. router
novell-rip
Question 20:
Where does the response to a GNS request come
from if there is both a Cisco router and a NetWare server on the same LAN?
A. Router
B. Local
NetWare server
C. Local SAP
server
D. Switch
Question 21:
What is the encapsulation type on a router for a
Novell network running version 3.12?
A.
Novell-ether
B. ARPA
C. SNAP
D. SAP
Question 22:
What is the default type of routing protocol
used by Novell NetWare?
A. Link-state
B. Distance
vector
C. Hybrid
D. OSPF
Question 23:
Which metrics does Novell RIP use?
A. Bandwidth
and delay
B. Ticks and
hop count
C. Distance
and cost
D. Size and
throughput
Question 24:
What does IPX use in the host portion of an
address to eliminate the use of ARP requests?
A. SAP
B. SPX
C. MAC
D. RARPs
Question 25:
Which Cisco IOS command is used to check IPX SAP
updates?
A. show sap
routing updates
B. show sap
routing activity
C. debug ipx
sap activity
D. debug sap
routing activity
