Chapter
5 exam
Question 1:
For dynamic routing to work properly what must
routers send to other routers?
A. ARP
requests
B. RARP
packets
C. Static
routes
D. Timely
updates
Question 2:
What is a router's main responsibility when routing
packets?
A. Traffic
control
B. Collision
avoidance
C. Enforcing
security
D. Path
determination
Question 3:
What does dynamic routing rely on?
A.
Maintenance of an ARP table
B. Accurate
entry of static routes
C. Accurate
routing tables
D. Collision
forwarding
Question 4:
Distance-vector routing begins by identifying
which directly connected entity?
A. Routers
B. Ports
C. Switches
D. Networks
Question 5:
What is the maximum hop count associated with
IGRP?
A. 15
B. 50
C. 100
D. 255
Question 6:
Which of the following occurs when a router
tries to send information about a route back in the same direction it was
received.
A. Split
horizon
B. Poison
reverse update
C. Holddown
D. Routing
loop
Question 7:
Which routing protocol is used to communicate
between autonomous systems?
A. RIP
B. Ethernet
C. Token Ring
D. Exterior
routing protocols
Question 8:
Which of the following is a Cisco proprietary
protocol?
A. IGRP
B. RIP
C. OSPF
D. ISIS
Question 9:
Routers under a common administration are said
to belong to what?
A. A WAN
B. A LAN
C. An AS
D. An SNMP
Question 10:
Entries made by an administrator to manipulate a
routing table are referred to as which of the following?
A. Static
routes
B. Dynamic
routes
C. ARP tables
D. Routing
tables
Question 11:
Which of the following are primary goals of
routing protocols?
1. Point-to-multipoint routing
2. Rapid convergence
3. Efficiency
4. Flexibility
5. Microsegmentation
A. 1, 2, 3
B. 2, 3, 4
C. 3, 4, 5
D. 1, 3, 5
Question 12:
What type of information is automatically
adjusted as topology changes occur?
A. Static
routes
B. Dynamic
routes
C. ARP tables
D. RARP
tables
Question 13:
Select the correct IOS command for configuring
IGRP as the routing protocol.
A.
Router#router igrp 100
B.
Router(config-router)>router igrp 100
C.
Router(config)#router igrp 100
D.
Router(config-if)#set router igrp 100
Question 14:
Which of the following is another term for
shortest path first routing algorithm?
A. Source
bridging
B.
Store-and-forward
C.
Distance-vector
D. Link state
Question 15:
What do routers use to make forwarding
decisions?
A. Routing
tables
B. VLANs
C. WAN
connectivity
D. Proximity
Question 16:
What passes periodic copies of routing tables
from router to router?
A. Link state
B. Distance
vector
C.
Store-and-forward
D.
Cut-through
Question 17:
What causes routing loops?
A. Path
determination is optimized
B. Hop count
is set below 50
C.
Convergence is present
D. Routing
tables have not converged
Question 18:
What allows a router to accept a packet on one
interface and forward it to another interface?
A. Broadcast
forwarding
B. Switching
function
C. Filter and
control function
D. Path
determination
Question 19:
What two parts can most protocol addressing
schemes be broken down into?
A. TCP and IP
B. IPX and
SPX
C. Network
and broadcast
D. Network
and host
Question 20:
At what time interval does IGRP send routing
updates?
A. 120
seconds
B. 30 seconds
C. 60 seconds
D. 90 seconds
Question 21:
Which routing protocols would most likely be
found running on a multiprotocol router?
A. IPX/SPX
and RIP
B. RIP and
TCP/IP
C. AppleTalk
and IGRP
D. RIP and
IGRP
Question 22:
Which of the options below gives two basic steps
required when configuring a routing protocol?
1. Configure the interface
2. Enable the routing protocol
3. Disable routing updates
4. Add the network numbers
A. 1, 2
B. 2, 3
C. 2, 4
D. 3, 4
Question 23:
Which of the following refers to the number of
routers a packet must pass through?
A. Bandwidth
B. Hop count
C. Tick count
D. Delay
Question 24:
Which OSI layer is responsible for finding the
best path through the internetwork?
A. 1
B. 2
C. 3
D. 4
Question 25:
What do routers use to communicate with other
routers?
A. Broadcast
forwarding
B. IP
Tunneling
C. Routing
protocols
D. Routed
protocols
