Exam Chapters 5&6:
Question 1:
You want to create a message to let people know a little something about the network or router when they log on - what command enables you to do this?
A. banner
msg
B. banner
motd
C. daily
msg
D. daily
motd
Question 2:
Where is the configuration file saved when you complete the setup process?
A. RAM
B. ROM
C. NVRAM
D. TFTP
Server
Question 3:
What is the function of the reload command?
A. It
reboots the router
B. It
saves the new IOS to Flash memory
C. It
loads a new configuration file in NVRAM
D. It
loads a configuration file from a TFTP server
Question 4:
You have connected a new LAN and made appropriate changes to your Cisco router configuration. What command do you issue to save the new version of the configuration file to NVRAM?
A. copy
config startup-config
B. copy
running-config startup-config
C.
configure memory
D. copy
running-config nvram
Question 5:
Which password is encrypted in the configuration file by default?
A. Console
B. Enable
C. Enable
secret
D. Virtual
terminal
Question 6:
Which command will save an active configuration?
A. config
t 
B. config
memory 
C. copy
startup-config running-config 
D. copy
running-config startup-config 
Question 7:
What is the first global configuration parameter set when using the setup mode?
A. enable
password
B. routing
protocol
C. host
name of the router
D.
interface configuration
Question 8:
Which Cisco IOS command displays the backup configuration file stored in NVRAM?
A. Router#
show flash
B. Router#
show nvram
C. Router#
show running-config
D. Router#
show startup-config
Question 9:
While in setup mode on a Cisco router, what is used to display default settings for configuration purposes?
A. pound
signs - example #yes#
B.
parentheses - example (yes)
C. percent
signs - example %yes%
D. square
brackets - example [yes]
Question 10:
Which keys are pressed to leave configuration mode completely and return the router to privileged EXEC mode?
A. ESC
B. CTRL-C
C. CTRL-Z
D.
CTRL-SHIFT-6 , X
Question 11:
What is the function of the erase startup-config command?
A. It
deletes the current IOS from NVRAM
B. It
deletes the configuration file in RAM
C. It
deletes the configuration file in NVRAM
D. It
deletes the bootstrap image from Flash memory
Question 12:
Which command is used to backup the active configuration file from a router to a network server?
A. copy
tftp startup-config
B. copy
running-config tftp
C. copy
tftp flash
D. copy
NVRAM tftp
Question 13:
Which keys are pressed in the escape sequence to terminate the initial configuration while in setup mode?
A. ESC
B. CTRL-C
C.
CTRL-ESC
D.
CTRL-SHIFT-6 , X
Question 14:
Where is the next place a router looks if it cannot find the IOS image in flash?
A. RAM
B. ROM
C. TFTP
D. NVRAM
Question 15:
Which of the following is the correct order of steps in the Cisco router system startup routine?
1. locate and load entire configuration file
2. locate and load operating system
3. load bootstrap
4. test hardware
A. 4,3,2,1
B. 4,3,1,2
C. 2,3,4,1
D. 3,1,4,2
Question 16:
What is an important result of the configuration file loading onto a router?
A. Causes
other instructions to be loaded into memory
B.
Executes diagnostics that verify the basic operation of router hardware
C.
Determines the router hardware and software components and lists them on the
console terminal
D. Starts
routing processes, supplies addresses for interfaces, and sets up media
characteristics
Question 17:
How does the router prompt appear when you are in global configuration mode?
A. Router#
B.
Router-config#
C.
Router(config)#
D.
Router(config-router)#
Question 18:
Which of the following is the correct order in which a router boots and looks for files?
1. Bootstrap from ROM
2. Config from NVRAM
3. Config from setup
4. Config from tftp
5. IOS from flash
6. IOS from ROM
7. IOS from tftp
A. 5,7,6,1,2,4,3
B.
1,5,7,6,3,2,4
C.
1,2,5,4,3,7,6
D.
1,5,7,6,2,4,3
Question 19:
Once you have selected an interface to configure, which prompt would be on the screen?
A.
Router(config)#
B.
Router(config-in)#
C.
Router(config-intf)#
D. Router(config-if)#
Question 20:
What is the logical order of steps to use when configuring a router?
1. If necessary, modify or remove changes
2. Examine the changes you have made
3. Save the changes to NVRAM
4. Enter confuguration statements
5. Examine backup file
A. 2, 1,
4, 5, 3
B. 3, 2,
4, 5, 1
C. 4, 2,
1, 3, 5
D. 5, 4,
3, 2, 1
Question 21:
What is an important function of the power-up self test (POST)?
A. Causes
other instructions to be loaded into memory
B.
Executes diagnostics that verify the basic operation of router hardware
C.
Determines the router hardware and software components and lists them on the
console terminal
D. Starts
routing processes, supplies addresses for interfaces, and sets up media
characteristics
Question 22:
When setting passwords for vty 0 4, what are you setting a password for?
A. Modem
connections
B. Line
consoles
C. Telnet
sessions
D. Remote
host router
