Site hosted by Angelfire.com: Build your free website today!

Ortho 9 Drawing

Do the following for the ortho 9 drawing:

 

 

Do the following for the ortho 9 drawing:

  1. Open you rectangle drawing
  2. draw a diagonal line in the projection view going from the lower left to the upper right.
  3. delete all the top, front and side labels,all dimensions.

** To put in diagonal line and fillet, slot and hole **

  1. line <enter>
  2. 3,4.5
  3. 1,3 <enter> 2x
  4. line
  5. 4.5,1.5
  6. 7,2.5 <enter> 2x
  7. ortho on
  8. line
  9. 3.5,3
  10. cursor right
  11. 2 <enter>
  12. cursor up
  13. 1 <enter>
  14. cursor left
  15. 2<enter>
  16. c <enter>
  17. circle
  18. click on upper right corner of front view
  19. 1 <enter>
  20. trim
  21. select circle as cutting edge<enter>
  22. click on two lines inside of circle <enter>
  23. trim <enter>
  24. select two lines connected to circle on front view<enter>
  25. click on circle on outside between lines<enter>
  26. trim <enter>
  27. select diagonal line on lower right of front view as cutting edge<enter>
  28. select the two lines in the lower right corner to trim them <enter>
  29. trim <enter>
  30. select diagonal line on upper left of front view as cutting edge<enter>
  31. select two lines intersecting the upper left corner to trim them<enter>
  32. circle <enter>
  33. 9,3.5 <enter>
  34. .5 <enter> 2x
  35. ***lines on top view***
  36. ortho on
  37. line
  38. 7.25,6.5
  39. cursor left
  40. 6.5 <enter> 2x
  41. select and change linetype to centerline
  42. line
  43. 7,6
  44. cursor left
  45. 6 <enter> 2x
  46. line
  47. 7,7
  48. cursor left
  49. 6 <enter> 2x
  50. line
  51. 3,5.5
  52. cursor up
  53. 2 <enter> 2x
  54. line
  55. 3.5,5.5
  56. cursor up
  57. 2 <enter> 2x
  58. line
  59. 5.5,5.5
  60. cursor up
  61. 2 <enter> 2x
  62. line
  63. 6,5.5
  64. cursor up
  65. 2 <enter> 2x
  66. select and change correct lines to hidden lines
  67. select and change correct line to center line
  68. ortho on
  69. line
  70. 8,7 <enter>
  71. cursor right
  72. 1.5 <enter>
  73. cursor down
  74. 1.5 <enter> 2x
  75. line
  76. 8,6
  77. cursor right
  78. .5
  79. cursor down
  80. .5 <enter> 2x
  81. select and change lines to hidden lines
  82. line
  83. 7.75, 6.5
  84. cursor right
  85. 1.25 <enter>
  86. cursor down
  87. 1.25 <enter> 2x
  88. select and change lines drawn to center line
  89. line
  90. 9,4.75
  91. cursor down
  92. 2 <enter> 2x
  93. select and change linetype to centerline
  94. line
  95. 8,4
  96. cursor right
  97. 2 <enter> 2x
  98. line
  99. 8,3
  100. 2<enter> 2x
  101. select and change last two lines drawn to hidden lines
  102. line
  103. 8,2.5
  104. cursor right
  105. 2 <enter> 2x
  106. line
  107. 8,3.5
  108. cursor right
  109. .5 <enter> 2x
  110. line
  111. 9.5, 3.5
  112. cursor right
  113. .5 <enter> 2x
  114. **dimension the part as shown in the sample drawing***
  115. you’re done!
  116. save the drawing as ortho9
  117. put in your binder.