7.3 Fuel filter orifice/check
valve; 3/16" |
E8TZ-9K061-A |
7.3 Fuel filter orifice/check
valve; 1/4" |
E9TZ-9K061-A |
7.3 Fuel filter
orifice--1/4"--spring and check ball |
F2TZ-9K061-A |
7.3 E-van fuel filter outlet
fitting |
E8TZ-9C402-A |
Injector return cap O-rings |
E6TZ-9229-AA |
Injector return caps--Prefix
determines barb size, suffix determines barb position |
|
1/4" barb for 3/16"
hose |
E3TZ-9A564-A; two nipple |
|
E6TZ-9A564-A; single nipple |
|
E6TZ-9A564-B; 90 degree |
5/14" serrated barb for
1/4" hose |
E9TZ-9A564-A; two nipple |
|
E9TZ-9A564-B; 90 degree |
|
F3TZ-9A564-A; single nipple,
#7 IDI Turbo |
|
F3TZ-9A564-B; three nipple,
#'s 5&6 IDI Turbo |
Filter return "tee";
early 6.9 |
E3TZ-9N290-A |
Return line hose clamps;
3/16" |
E7TZ-9B255-C |
Return line hose clamps;
1/4" |
E9TZ-9B255-A |
|
|
Fuel line seals--filter to
injection pump |
E3TZ-9K260-A |
Fuel line seals--fuel filter
inlet; return line from injection pump (rear only on some applications) |
E3TZ-9C387-A |
Injection pump inlet fitting
o-ring |
E3TZ-9N693-A |
Transfer pump cover
lock-block/pressure tap o-ring |
E3TZ-9N693-B |
Injection pump outlet check
valve o-ring |
E8TZ-9E583-A |
Engine temperature
sender--magnetic gauge |
F1SZ-10884-A |
Engine overheat switch--light |
F3TZ-10884-A |
Cold start switch--fast idle
solenoid and timing advance |
E8TZ-9E939-A |
Fast idle solenoid |
E5TZ-12B526-A |
7.3 Restriced fuel filter
sensor (vacuum switch) |
E8TZ-9S283-A |
Fuel filter air bleed fitting
and schrader |
1 1/2" long:
E3TZ-9F597-A; 6.9, early 7.3 |
7.3 Fuel heater--mounts in
filter header |
F2TZ-9J294-A |
7.3 Fuel heater o-ring |
E8TZ-9K342-A |
7.3 Water seperator sedimate
bowl and schrader |
E8TZ-9A353-A |
7.3 Water seperator drain kit |
E8TZ-9J305-A |
Water in fuel sensor |
E8TZ-9J308-A |
Water in fuel sensor o-ring |
E8TZ-9B268-A |
Glow plug controller, 83-86;
screws into rear of block |
F3TZ-9A444-C |
Glow plug power relay, 83-86;
mounts on RH fender |
E3TF-12A343-C |
After-glow relay, 83; mounted
in front of RH battery on fender |
E2TZ-9C972-A |
Wait lamp latching relay, 83;
under dash near diesel warning light module (contains wait, water in fuel,
filter lamps) |
E3TZ-12B536-A |
Glow plug intergrated
controller/relay--87 and up; longer "wait" light time |
F0TZ-12B533-A |
Injection pump gear bolts |
NAPA P/N 331-10 (U-joint
hardware kit) |
Crankcase Depression
Regulator-valley pan or valve cover grommet |
E3TZ-6A892-A |
CDR tube and grommet assembly |
E8TZ-6A892-A |
Turbo oil drain to valley
grommet |
F3TZ-6853-A |
Turbo oil drain to intake
o-ring |
F3TZ6A892-C |
Turbo to drain o-ring |
F3TZ-6N653-B |
Turbo oil inlet adapter gasket |
F3TZ-6N652-B |
Turbo oil supply tube seal |
1819772-C1 |
Turbo to intake adapter o-ring |
F3TZ-9E463-A |
Turbo adapter to intake gasket |
F3TZ-9654-A |
Turbo exhaust inlet gasket |
F3TZ-6N640-A |
Engine RPM sensor |
E5TZ-17B384-A |
Silicone sealer; gray,
caulking gun cartridge |
F5TZ-19G204-AB or Waker T-95 |
Flange sealer; 6.9 intake
gasket, head side around coolant passages; 7.3 fuel system NPT fittings |
Loctite 515 Gasket Eliminator |
Rear main seal-saver sleeve
sealant |
Loctite RC/620 or Permitex 3H
Aviation Gasket Sealer Liquid |
Flywheel-to-crankshaft bolt
sealer; holes that pass through crank flange |
Teflon pipe sealant/ Loctite
PST |
Silicone dielectric grease |
Used to lube injector return
O-rings and caps to aid assembly |
Fuel lubricity additive |
F8AZ-9C077-AA or Stanadyne All
Season Diesel Fuel Conditioner P/N 29409(pt) |
Cooling system conditioner |
Ford FW-15/-16 or Fleeguard
DCA4 |
Cooling system test strips |
Fleetguard P/N CC2602 |
Cooling system sealer; use if
cylinder wall deterioration (pin holes) are suspected |
Irontite Ceramic Cooling
System Sealer |
Front
End Accessory Drive (FEAD) belt and tensioner application
"Serpentine" belt-equiped engines
Standard F-series and E-van with
130 amp alternator:
92 and 93 with
"cassette" type tensioner; TORX-head retaining bolt
Belt--F5TZ-8620-CB;
Tensioner--F2TZ-6B209-D
92-94 with "damped"
type tensioner; 13mm-head retaining bolt
Belt--F4TZ-8620-T;
Tensioner--F4TZ-6B209-A
92-94 with "shock"
type tensioner
Belt--F4TZ-8620-T;
Tesioner--F4TZ-6B209-C
All above should have belt guide
F5TZ-8680-AA installed on vacuum pump.
92-94 Ambulance package and
school bus with 130 amp alternator:
Should have Recall 96B83 update
kit F5PZ-8A630-BA installed; "shock" type tensioner
Belt--F4TZ-8620-T;
Tensioner--F4TZ-6B209-C
92-94 Ambulance package and
school bus with 160 amp alternator:
Should have Recall 96B83 update
kit F5TZ-8A630-AA installed; "shock" type tensioner
Belt--F4TZ-8620-L;
Tensioner--F4TZ-6B209-C
All vehicles listed use flanged
idler pulley F5TZ-8687-BA
The correct belt fits tight.
To install it will be necessary to remove the outboard alternator bolts, loosen
the inboard bolt and pivot the alternator to slip the the belt over the pulley
while holding the tensioner against its stop. Install and tighten the
alternator bolts before releasing the tensioner.