PURE DATA, LTD.

PDI7023-16FL

NIC Type          Ethernet
Transfer Rate     10Mbps
Data Bus          16-bit ISA
Topology          Star
Wiring Type       62.5/125 m m Fiber optic cable (e.g. Belden
                  227412)
Boot ROM          Not available

[Image]

                                         INTERRUPT REQUEST

   IRQ      E2A      E2B      E2C      E2D      E2E      E2F      E2G      E2H     E2I      E2J

      2/9   Open     Open     Open     Open    Closed   Open     Open     Open     Open     Open

      3     Open     Open     Open     Open    Open     Open     Open     Open     Open    Closed

  »   4     Open     Open     Open     Open    Open     Open     Open     Open    Closed    Open

      5     Open     Open     Open     Open    Open     Open     Open     Closed   Open     Open

      6     Open     Open     Open     Open    Open     Open     Closed   Open     Open     Open

      7     Open     Open     Open     Open    Open     Closed   Open     Open     Open     Open

      10    Open     Open     Open    Closed   Open     Open     Open     Open     Open     Open

      11    Open     Open    Closed    Open    Open     Open     Open     Open     Open     Open

      12    Open    Closed    Open     Open    Open     Open     Open     Open     Open     Open

      15   Closed    Open     Open     Open    Open     Open     Open     Open     Open     Open

                             LOOP BACK ENABLE

                 Setting                                E7

  »                Disabled                      Pins 1 & 2 closed

                   Enabled                       Pins 2 & 3 closed

  Note:The loop back is used with diagnostic software to trouble-shoot
  the card.

                             I/O BASE ADDRESS

       Address              SW1/1             SW1/2            SW1/3

           260h               On                On               On

           290h              Off                On               On

           2E0h               On               Off               On

           2F0h              Off               Off               On

  »        300h               On                On              Off

           350h              Off                On              Off

           380h               On               Off              Off

           3E0h              Off               Off              Off

                             JUMPER E6 ENABLE

                 Setting                               SW1/5

  »                 Enabled                              On

                   Disabled                             Off

  Note:If this option is disabled (SW1/5 Off) the options selected using
  E6 are disabled.

       EXTENDED TRANSMIT TIMEOUT AND SIGNAL QUALITY ERROR (SQE) TEST

    Timeout           SQE            E6A           E6B            E6C

    Enabled         Enabled         Closed         Open          Open

    Disabled        Disabled         Open         Closed         Open

    Enabled         Disabled         Open          Open         Closed

  Note:SW1/5 must be set to on for these settings to be valid.

  With extended transmit timeout enabled, if the card is transmitting for
  an extented amount of time the transmission will be interrupted and
  continued after a preset time. This keeps the card from dominating the
  network.

  Signal Quality Error (SQE) is a test of the collision circuitry and
  path.

  E6A, E6B, and E6C are located on the PIM module.

                            LINK INTEGRITY TEST

                 Setting                               SW1/7

  »                 Enabled                              On

                   Disabled                             Off

  Note:E7 is located on the PIM module.

  FACTORY CONFIGURED SETTINGS

     Switch         Setting

     SW1/4            Off

     SW1/6             On

     SW1/8            Off

                            DIAGNOSTIC LED(S)

   LED      Color    Status                    Condition

   LED1     Green      On              Data is being transmitted

   LED1     Green     Off            Data is not being transmitted

   LED2     Amber      On               Data is being received

   LED2     Amber     Off             Data is not being received

   LED3     Amber      On             Network connection is good

   LED3     Amber     Off            Network connection is broken

   LED4      Red       On      Card is transmitting for an extended time

   LED4      Red      Off                  Normal operation

   LED5      Red       On            Collision detected on network

   LED5      Red      Off                  Normal operation