DANPEX CORPORATION

EN-2200BT

NIC Type      Ethernet
Transfer Rate 10Mbps
Data Bus      16-bit ISA
Topology      Star

              Linear bus
Wiring Type   RG58A/U 50ohm coaxial

              Shielded/Unshielded twisted pair

              AUI transceiver via DB-15 port
Boot ROM      Available

[Image]

                               ACTIVITY LED

               Setting                                 JP1

               Enabled                               Closed

               Disabled                               Open

  Note:If the network hub has an activity LED for each line, setting this
  option to "enabled" will allow the hub LED to

                            LINK INTEGRITY TEST

                Setting                                 JP2

  »                Enabled                       Pins 1 & 2 closed

                  Disabled                       Pins 2 & 3 closed

  Note:The link integrity test is valid only when the cable type is
  shielded/unshielded twisted pair.

                                CABLE TYPE

                Type                        JP3            JP6A - JP6F

         RG58A/U 50ohm coaxial           Pins 2 & 3         Pins 1 & 2
                                          closed             closed

  »    Shielded/Unshielded twisted       Pins 1 & 2            N/A
                  pair                    closed

        AUI transceiver via DB-15        Pins 2 & 3         Pins 2 & 3
                  port                    closed             closed

  Note:When the cable type is twisted pair, the settings for JP6A - JP6F
  are not used.

                                WAIT STATE

           Setting                    JP4                    JP5

  »       0 wait states               Open                   Open

          1 wait state                Open                  Closed

          2 wait states              Closed                  Open

                            ONBOARD TERMINATOR

                Setting                                 JP7

  »               Disabled                       Pins 1 & 2 closed

                   Enabled                       Pin 2 & 3 closed

  Note:If the card is on either side of a coaxial segment, the onboard
  terminator can be enabled instead of using an

                                 BOOT ROM

                 Setting                               JP9A

  »               Disabled                             Open

                   Enabled                            Closed

                             BOOT ROM ADDRESS

  Boot ROM Address         JP9B              JP9C              JP9D

       C8000h             Closed             Open             Closed

       CC000h              Open              Open             Closed

       D0000h             Closed            Closed             Open

       D4000h              Open             Closed             Open

                             I/O BASE ADDRESS

        I/O Address                 JP9E                    JP9F

  »          300h                  Closed                  Closed

             320h                   Open                   Closed

             340h                  Closed                   Open

             360h                   Open                    Open

                             INTERRUPT REQUEST

   IRQ      JP10A    JP10B    JP10C    JP10D    JP10E    JP10F     JP10G

      2/9   Closed   Open      Open     Open     Open     Open     Open

  »   3     Open     Closed    Open     Open     Open     Open     Open

      4     Open     Open     Closed    Open     Open     Open     Open

      5     Open     Open      Open    Closed    Open     Open     Open

      10    Open     Open      Open     Open    Closed    Open     Open

      12    Open     Open      Open     Open     Open    Closed    Open

      15    Open     Open      Open     Open     Open     Open    Closed

                             DIAGNOSTIC LED(S)

       LED               Status                     Condition

       LED1             Blinking            Data is being transmitted

       LED1                Off            Data is not being transmitted

       LED2                On            Twisted pair connection is good

       LED2                Off              Twisted pair connection is
                                                      broken

       LED3             Blinking              Data is being received

       LED3                Off              Data is not being received

       LED4                On             Collision detected on network

       LED4                Off               No collisions detected on
                                                     network

  Note:LED2 will only funtion when the cable type is twisted pair,
  otherwise LED2 will remain off.