Test Mode
Codes | Phone Models | Programming | Test Mode
You can access the test mode by holding down the *, 2, and the left (RCL) button, you then tap the end button. The screen should go blank and then TEST MODE USA (where applicable), phone type, and the number of NAMs (I guess, it says Ph2). Here are the commands that I have discovered on my CDM 4500 CDMA. If you have ANY comments, suggestions, or updates you can direct them to
Djdunkman@Hotmail.com
The test mode on audiovox phones is like that of many other phones of different brands. The test mode will allow you to test various phone functions. Mode doesn't support variables within the initial command string. For example on Motorola phones to change the channel you could use 11xxx, xxx being the new channel, on the audiovox you have to use the 31 command and then select the channel within the command interface.
Some basic info:
You can get letters by pressing * then:
1 |
2 |
3 |
4 |
5 |
6 |
A |
B |
C |
D |
E |
F |
Ok you've waited long enough, here are the codes as I know them.
More codes and explanations to be added soon, so check back often!
Code # |
Code name |
Extra info |
000 |
Phone Mode |
Displays CDMA mode |
001 |
Fm mode |
Activates FM Mode? |
003 |
PA_ON |
Turns PA (?) on |
008 |
REG read addr |
Excepts 3 digit address (press V+ to enter), outputs 4 digit data string |
009 |
REG write addr |
Same as above except you write 4 digit sting |
012 |
IDLE |
Phone status or test mode status? Returns "IDLE" |
013 |
RXTX ch |
Changes TX/RX channel, see 31 command |
021 |
RX_AGC_ADJ |
|
022 |
TX_AGC_ADJ |
|
023 |
LNA_GAIN_VAL |
Sets the LNA gain value |
030 |
TRK_LO_ADJ |
|
031 |
PLLSYN ch |
PLL Synthesis CH. This command can be used to receive analog audio. Similar to Motorola's 11# command |
040 |
I_OFFSET |
|
041 |
Q_OFFSET |
|
050 |
PA_GAIN |
Adjusts PA gain |
053 |
AGC_GAIN_TM |
|
061 |
LNA_FALL |
|
062 |
LNA_RISE |
|
068 |
AGC_VALUE |
|
069 |
RASRAM Select |
|
070 |
RSSI |
|
071 |
RSSI_CONST |
|
072 |
RX unmute |
Turns mute off for reception. Turns off |
073 |
RX mute |
Mutes reception |
074 |
TX unmute |
|
075 |
TX mute |
|
076 |
Comp_on |
|
077 |
Comp_Bypas |
|
078 |
Audio Read Address |
|
079 |
Audio Write Address |
|
080 |
TX_GAIN_LMT |
|
081 |
TX_OPEN_LOOP |
|
082 |
TX_GAIN_AJ_R |
|
083 |
TX_GAIN_AJ_W |
|
084 |
TX_GAIN_CTL |
|
085 |
ICH CUTOFF |
|
086 |
QCH OFF |
|
087 |
RX unmute 2 |
|
088 |
RX mute 2 |
|
089 |
Audio Test |
|
090 |
DFM_Reset |
|
091 |
VOC_Reset |
|
092 |
VOC_DEC_VOL |
|
094 |
WBD Transmit |
|
099 |
Download |
This command basicly shuts down your phone. Any info??? |
100 |
PLSET 1 |
|
101 |
PLSET 2 |
|
102 |
Set ATTN |
Sets Attenuation (weakens signal) |
103 |
APC_ON/OFF |
|
104 |
TONE PATH frq? |
|
105 |
FREQ SENS |
|
106 |
SAT_LEVEL |
|
107 |
TX_DEVIATION |
|
108 |
FM TX GAIN |
|
109 |
FM RX GAIN |
|
110 |
LNA_OFFSET |
|
114 |
PA_DET_IDEAL |
|
115 |
PA_RO |
|
116 |
PA_R_RISE r_rise |
|
117 |
PA_R_FALL f_fall |
|
118 |
PDM1_VAL |
|
119 |
PDM2_VAL |
|
120 |
INVM data write |
|
121 |
Free_write |
|
122 |
Free_read |
|
123 |
Write A-key |
|
124 |
INAM data write |
|
125 |
Software version |
|
126 |
ESN read |
|
127 |
Scode read |
|
128 |
Lcode read |
|
129 |
WFTV write (data) |
|
130 |
RSSI_Adj |
See RSSI Note at the beginning of this page |
131 |
Audio |
Turns on audio used in conjunction with the 31 command |
132 |
PLSET |
|
133 |
Read RSSI |
See RSSI Note at the beginning of this page |
134 |
Low V Det |
|
135 |
Test Version |
|
137 |
FSCode read |
|
138 |
NPCode read |
|
139 |
DSCode read |
|
140 |
INIT |
Restarts test mode. Screen should quickly flicker after INIT (Initialize) flashes on the screen. |
141 |
Restart |
Reboots the phone in normal mode |
142 |
LCD Check |
Runs through a LCD check (lights all digits) |
143 |
SPEED CHG |
Activates the top LED when 1 then V+ keys are pressed. When the light is on, 0 and V+ will turn the light off. |
144 |
WNAM_AMPS data-write |
|
145 |
WNAM_CDMA data-write |
|
146 |
DTMF_TX_Gain |
|
147 |
Easy Test |
|
148 |
Hard Version |
|
149 |
Timer reset |
|
150 |
Charge |
|
151 |
Battery Stats |
This is cool shows bat temp |
152 |
Preset Write |
|
153 |
Parts Read |
|
154 |
PRL ID read |
|
185 |
AUDIO_PASS |
|
186 |
TONE_CONT |
|
188 |
Sounder mode |
Rings the phone when audio is enabled, Also changes the rate at which the phone vibrates when you activate 193 first. |
193 |
VIB mode |
Activates vibrating motor (short pulses) |
200 |
FAIL History |
|
201 |
Call History |
|
212 |
RTC_SET |
For more info on commands 212 - 214 and 242 see real time clock note at top |
213 |
RTC_READ |
see real time clock note at top |
214 |
RTC_Clear |
see real time clock note at top |
215 |
Beta_loop |
|
217 |
Bank_ver |
|
218 |
Ram_read |
|
219 |
Ram_write |
|
223 |
WNV |
|
230 |
LCD_Bright |
Lets you adjust the contrast of the LCD display from 0 to F (0 being very light, F very dark). Note that A-F are 10 - 15 |
237 |
FSCode read |
Security code? |
242 |
RTC_REG read |
see real time clock note at top |
255 |
Rel_Date |
Displays the release date |
Codes | Phone Models | Programming | Test Mode
© 2003
DJX Media site design. All Rights Reserved