|
|
|
Pattern for Making Character Pens
Preparing the Pens:The reason for the use of the Papermate Flexgrip Ultra Ball Point Pens is because you can unscrew the bottom silver part of the pen and remove the ink cartridge, which you will need to do to bake the polymer clay onto the empty pen cartridge. You will be working with two pens; one you will be making into a character pen and the other one will be used as a rolling pin. Using the Character Face Mold or other commercial face mold:Roll up a piece of the flesh-colored polymer clay into a smooth ball, about the size of the push mold cavity, and roll one end of the ball into a cone shape. Put the tip of the cone into the nose cavity of the push mold. Holding the clay as steady as possible, push the clay straight into the push mold and fill to capacity. Using another piece of flesh-colored polymer clay, push the clay onto the clay inside the push mold. This will act as a handle and help you to remove the character face. Using a toothpick, poke nostrils into the nose area. Put aside your character face. Covering the Pen Cartridge:Following the pictures included in this free website, roll out a very thin (1/16th inch) pancake of clay, using your second pen as a rolling pin to smooth out the clay, and cover the outside of the pen. You can use a marble effect, or stripes; be creative. For purposes of explanation, I will explain the project using the Santa above. Roll out the 1/16th inch pancake of red clay. Using your x-acto knife, and your pen to measure, cut a rectangle of clay approximately 1.5 inches wide and the length of the pen barrel. Wrap the red clay rectangle around the pen barrel and cut away any excess clay. If you are "short" in any areas, you can "patch" a little clay onto the area and smooth with your fingers until the creases and lines disappear. Creating the Pen Head:Attach the Santa Face to the top of the pen. It will stick to the red clay already on the pen. Roll up another small flesh-colored clay ball, about 1/2 inch in diameter. Push your finger into one side of the ball, creating a conclave identation. Put this ball onto the back of the pen to create a "back of Santa's head". It doesn't have to be perfect. It will be covered with Santa's hair. Using your smoothing tool or your finger, you can smooth the sides of the head to make sure it is attached firmly. Remember the heads will be covered with hair and sometimes with hats. Making Santa's HatFor Santa's hat, as well as the Wizard's hat, you take a 2 inch diameter ball of red clay and roll into a cone shape. Poke and smooth a hold in the thick side of the cone to create an opening to fit the head into. Smooth the edges/rim of the hat and make sure it is an even rim.
Safety Instruction: Any tool, plate, dish, spoon, or other tool used with polymer clay can no longer be used in food service. For example: If you use the garlic press to make Santa's hair in the next step, you can no longer use it to press garlic. You will need to get a new one to use with food. Your first garlic press will automatically become a member of your clay tool set. If you use a dish or pan to bake the clay figures in, they are no longer suitable for food service. A good substitute is the ceramic tile or even a tin inexpensive pie plate.Using the garlic press or a piece of screening, take white clay, roll it into a thick ball, and press or push it through the press or the screen. It will produce the tiny, tiny strands of hair. Attach one clump of white clay hair at a time to creat the hair and beard. To create the mustache, you will need to remove one strand and lay between the nose and mouth. To make the fur on Santa's hat, you will put the white clay through the press or screen and only use short clumps of the strands. Attach them to the rim of the hat and the tip fo the hat until you have a nice layer of fur. You can take two tiny brown peas of clay or white peas of clay and make small think circles and attach as buttons. A cocktail straw is a good tool to use for this. But you can make them without the straw too. Be sure to poke two sew marks through the buttons. Details count! You will be baking the hat and pen separately and gluing them when completed. To make the Pen Base/HolderLook at the picture of the Santa pen and roll up a large ball of clay about the size of the pen base. This is a good project for any left over scraps of clay from other projects. To use the left over clay, roll up a ball of multi-colored clay about the size of the pen base. Then roll out the red clay and make a very large, thin pancacke out of it. Cover the mound of multi-colored clay and smooth down the sides. Cover the bottom if you have enough clay, although it's not necessary. Uisng your spare rolling pin pen, push the pen into the top of the base/hold and wiggle just a little bit and remove the pen. You have now made the cavity that will hold the pen when completed. Roll out a long white coil of clay and another long red coil of clay. Twist together to get the candy-cane effect. Wrap around the bottom of the pend base/holder and cut off any excess. You can add a small candy cane to the front of the base, using the same twisting method. Bake the polymer clay pen, hat and base according to the polymer clay manufacturer's baking instructions. Be careful to properly time your baking. It is crucial that you set a timer. Safety Precaution: Children should be supervised while baking polymer clay. Although it is a very safe product, if you overbake polymer clay, it will release toxic fumes. It is critically important that you set a timer when baking polymer clay so you do not overbake and release the toxic fumes.Painting the Character Pen Faces:1. Paint the eyes a yellowish/greyish white. Paint iris circles in blue or brown. Paint tiny black pupils and add a pin dot of white paint at 2:00 on the outside circumference of the pupil to finish the eyes. 2. Paint think wispy lines to create eyebrows. 3. Add red and brown and a little white paint together. Mix until you have a flesh-colored brownish pink. You don't want a lipstick pink; you want a lip-color pink. It helps to water down the paint mixture a little bit. It goes on more like a lip color rather than a lipstick. 4. Once the faces are dry, the pens are completed.
Other Tips on the Characters:For the Pink Fairy Pen, you can bake the doll bald and when cool, glue a little acrylic doll hair instead of making the hair out of clay. (Do not bake the acrylic hair) Her eaars are made by taking tiny balls of flesh-colored clay and shaping them into fairy ears. They are baked separately and glued on after the hair is applied. For the Nun and Mary Pen, the veils are made by rolling out large rectangles of 1/16th clay and cutting a straight edge on one long end. Drape te rectangle onto the top of the head and create folds and cut off the bottom into a pleasing shape. This technique can be used to make a Woman in Burka pen too. For the St. Patrick's Day pen, you can create the hat by using the picture as a guide. The hat is baked separately from the pen. The hat and the acrylic hair are glued onto the head after baking.
To Order the Character Push Mold used in this project, send a money order for $10.00, plus $3.50 shipping to: Regina Edmonds, 4890 NW 13th Terrace, Pompano Beach, FL 33064 or go to www.paypal.com and send $13.50 to fairy111@bellsouth.net. Be sure to include a note that you are ordering the Character Pen Push Mold. It will be mailed out promptly via USPS Priority Mail
Copyright by Regina Edmonds - 2000 Pompano Beach, Florida Free Project and New Product Notification Sign UpIf you would like to receive other free projects and be notified as to new product information. Send name, address, phone and email to me and I'll put you on the list: Thanks and I hope you enjoyed the pattern.
|
|
Free counters provided by Andale.
|
