The following is a list of the circuits and related sections that appear on this page. Select one of the internal page links or scroll down the page.
There are quite a few images contained in this page and it therefore may take a long time to download.
This page has a number of variations on transistor type throttles and related circuits. The throttles range from 'tried and true' to experimental designs. The basic transistor throttle serves as a base to which other circuits are added.
The Waveform diagrams shown on this page are not technically correct but are meant to illustrate of the throttle output wave forms for a given control setting.
The diagrams and texts start with the transformer and rectifier circuits and some throttle designs and on to the addition of other features such as unplugable walk around control. Some experimental throttles are also shown. The circuits although functional can also be used a guides for your own designs.
The first schematic is of the Direct Current power supply for the throttles. Shown is the primary and secondary circuits and the components needed to power the throttles. As this section of the throttles uses 120 volt AC power great caution should be taken in this area. All transformers should be mounted in a fully enclosed metal cabinet and properly grounded. Transformers for multiple units could be centrally located and the low voltage AC then routed to each throttle.
The first circuit is a 2 Amp, 0-12 Volt, voltage regulator type circuit. It uses a 10K ohm potentiometer to control the output voltage and has a light emitting diode that will indicate an overload condition. A DPDT toggle switch controls the train direction. The TIP142 output transistor will need a heat sink to keep it cool and the 0.33 ohm resistor should have a 5 Watt power rating. The OPAMP is one half of an LM 358. One quarter of a LM 324 could also be used.
In the next circuit walk around control is added to the throttle. A 4 conductor, 22 Gauge stranded cable will allow the operator to move around with the 'Hand Held Controller' while the power section of the throttle remains at a fixed location.
A DPDT 24 Volt DC relay and a toggle switch has been added for direction control. The direction switch, speed control potentiometer and a 10K ohm resistor are mounted in the Hand Held Controller.
A variation on the walkaround throttle is in the next circuit. If extra wires are added to the control cable they can be put to use for operating accessories on the layout.
For every extra wire 2 such loads can be controlled. Electromagnetic uncoupling ramps could be turned on and off, train whistles could be blown or a reverse loop switch can be thrown after the train has passed.
By using 4N33 Darlington output Optoisolators as low power relays and adding two push buttons or a toggle switch to the hand held controller a wide variety of external devices could be operated with only a small current draw on the throttle circuit itself.
Unplugable operation would still be a feasible option even with six wires in the control cable. This would allow four auxiliary control outputs.
The optoisolator by itself can only handle a load current of 20 milliamps, larger load currents require adding another transistor. The next drawing is shows a more detailed view of the auxiliary outputs.
Push button switches are shown in the schematic but these could be replaced with a SPDT switch if desired. The only limit to the auxiliary outputs is that both loads can not be operated at the same time or a short circuit will occur. The 100 ohm resistor protects against this in the push button system. A little creative wiring or a second wire could provide a solution when needed. Any number of extra wires could be added for more control outputs.
next up is the basic transistor throttle with unplugable walk around control added. The direction memory uses an LM339 quad comparator and has a delayed action so that the direction can not change if the throttle output is above a predetermined voltage.
The delayed reverse section, comparator section D, of the circuit grounds the bases of the transistors whenever the voltage at its PLUS input is higher than the reference voltage at the MINUS input. The PLUS input is connected to the throttle control voltage line.
When the transistor bases are grounded they cannot conduct and any changes at their emitters will have no effect until the control voltage again falls below the preset level.
Comparator sections B and C function as a voltage window detector. That is to say the outputs of both section Band C are high as long as the direction signal voltage is between 4 and 8 volts. If the signal goes below 4 volts or above 8 volts the appropriate output will go low and the direction will change accordingly.
If the controller is unplugged the direction signal will go to 6 volts and the train will maintain its last direction.
Please refer to the voltage comparator information page on this web site for help on how comparators work.
Voltage Comparator information page
The next throttle is one that was put together for testing purposes only. As can be seen it is a modification of the basic transistor throttle shown above. The SPDT switch allows the throttle to have a full or half wave DC output.
The value of the 8uF capacitors is calculated to allow the voltage across the 1000 ohm pot to decay to 1/3 of the input voltage before the next cycle starts. At 120Hz; 8uF is needed and at 60Hz; 16uF is required to achieve this result.
This all means that the output of the throttle has peak pulse voltage that is three time the lowest voltage of output at any given throttle setting. Please refer to the wave forms diagram below the schematic for clarification.
The throttle has automatic current limiting (2 amps maximum) and a semi-regulated output voltage.
This throttle gave pretty good results with an Atlas locomotive and one from a starter set of the type that make their appearance at Christmas time.
The next schematic is for an advanced type of pulse throttle. Simply put, as the output voltage is increased by the 10K pot, a pulse is injected onto the the control voltage at the PLUS input terminal of the second LM358 OpAmp. As the control voltage increases the width of the pulse is also increased.
The height of the pulse is adjusted so that at some point it is overtaken by the output of the first OpAmp section. From this point on the output from the throttle is pure DC
The duration of the pulse is adjusted so that it is at approximately 50% when the pulse voltage is overtaken by the output control voltage.
The pulse rate can also be varied but whenever the rate is adjusted the other variables of the oscillator will be thrown off and all would have to be reset.
To properly set up this particular throttle an osilliscope is required.
Overall this particular throttle did not perform as I had hoped it might, but seemed to work well for locomotives with good quality motors.
The next throttle is more than a little different, it's very different but in its own unique way it works just fine. It is however posted here for interest sake only and should not be viewed as a major discovery or some sort of magic trick.
The design uses the variable pulse width oscillator that is the at the heart of the "Variable Pulse Type Throttle" as shown above. The oscillator in this circuit however switches a current regulator constructed from an LM317 voltage regulator.
Rather than regulating the output voltage this throttle instead produces variable width pulses of a fixed current value, for example 200 or 400mA. The voltage can rise to a level that is determined largely by the B+ input voltage and the drop across the LM317 but the motor can only receive the maximum current that the LM317 will pass. This current value is determined by the value of R1.
It'll never work you say. It does work, however there are some drawbacks.
For example:
To determine the current pulse level for a particular engine, trial and error is required to find the best pulse current limit and frequency of pulses. A scope is necessary for this work.
The throttle should perform best with a single locomotive used for switching and yard work. It might be ideal for switching games on portable layouts.
This throttle although functional is also rather odd and as such should be viewed as perhaps being in the realm of weird science. The testing done on this design indicated that it will not harm motors in any way. In fact when the motor is operating at high RPM's the voltage across the motor will behave little different than for a normal power pack and current draw may be reduced. As the motor always receives a fixed current pulse, low speed cogging should be reduced to a very large extent. Under short circuit conditions the output current is restricted to the pulse current value.
While the LM317 performed as expected in this circuit it certainly not designed for this application and therefore may suffer a high failure rate although it held up during testing.
This page presents a throttle with Variable Frequency - Full wave Direct Current output. The throttle controls the train speed with variable output voltage but also allows the operator to change the frequency of the FWDC as well.
As with most throttles, the output voltage of this throttle controls the speed of the train. The variable frequency is intended to improve the operation of the motor itself. It has not yet been possible to test this throttle design an a large number of motor types but has shown good results under limited testing.
The throttle's output can be varied from 0 to approximately 10 Volts and through a frequency range of 16 to 90 Hertz full wave with the parts values shown on the schematic. (The calculated AC frequency range of the oscillator is 8 to 45 Hertz.)
This circuit, although functional, is strictly experimental and therefore it has not been designed for simplicity of construction. Separate power supplies are needed for both the oscillator and output sections of the circuit.
The throttle circuit is broken down into three sections and descriptions given for each. A complete but less detailed drawing of the throttle is shown farther down the page.
The following "Oscillator Section" schematic is the heart of this throttle. It contains an XR-2206 sine/square wave oscillator integrated circuit. This device is relatively expensive but is easy to use and has a very good frequency range and output waveform.
The output of the oscillator is buffered and amplified slightly by the LM358 operational amplifier and then passed through a full wave rectifier bridge.
The "Oscillator Section" of the throttle produces a FWDC output of approximately 4 Volts RMS which is varied through a potentiometer and then fed to the input of the throttles output section.
Full wave rectifiers double the frequency of the AC input. Because of this an input of 10 Hertz Alternating Current will produce an output of 20 Hz full wave Direct Current.
The output section of this throttle is a simple and rugged design with built in current limiting. It serves as a direct current power amplifier for the oscillator section and therefore eliminates the need for a powerful alternating current source.
"But how will I know the operating frequency of the throttle?", I hear you ask.
Fear not. This section shows a schematic for a "Frequency Meter", that will indicate the full wave DC output frequency of the oscillator section as measured across R10 at Test points 2 and 3.
The meter is built around the LM2917 - Frequency to Voltage converter chip that is designed for just this sort of application. Also shown is a 60Hz. source that can be used to calibrate the frequency meter.
The next schematic shows the three sections of the Variable Frequency Throttle as they would be connected together. The drawing is less detailed than the others but shows the interconnection of the separate circuits
As mentioned earlier the COMMON's of the Oscillator Section and Output Section cannot be connected together. Do not use one LM358 chip to do both functions in the complete circuit.
This throttle is an upgrade of the type of throttle that is supplied with many of the HO train sets that are popular at Christmas time. These throttles do not have a reversing switch but instead have a center OFF position on the speed control knob.
While this throttle may seam like a step backward in the evolution of train controls it does have features that make it useful in certain situations.
Due to its one control operation it would be ideal for small children and persons with reduced hand dexterity.
There is no chance of the direction suddenly being reversed while the train is under way as the output control would have to pass through ZERO in order to change direction.
It would also be possible to have a spring loaded, one axis joystick type control that would automatically stop the train when the lever is released and as there is only one control it could be as large as desired. Again this might be helpful for someone who could not easily manipulate small controls or small children who would have an easier time with just one control.
The above schematic shows the basic Toy Throttle. It is powered by a 24 Volts AC, Center Tapped transformer to provide PLUS and MINUS voltages.
The throttle uses a Push-Pull amplifier that eliminates the need for a reversing relay or switch.
When resistor R2 is in the CENTER position the throttles output voltage would be "ZERO". Adjusting R2 up or down would produce positive or negative voltage to the track thereby controlling the trains direction.
Resistors R1 and R3 limit the maximum output voltage to between PLUS or MINUS 10 Volts.
This next circuit is a variation on the Basic Toy throttle. In this version three push buttons are used to control the output.
Button S1 causes the train to move in one direction while S2 moves it in the other. Button S3 is the "Quick" or emergency brake that will stop the train very quickly.
An interesting feature of this system is that the train could be brought to a stop and then move off in the opposite direction by pressing only one button. Useful for shunting perhaps.
Resistors R5, R6, R7 and diodes D1, D2 form a voltage limiter that reduces the maximum output voltage swing as mentioned in the potentiometer controlled circuit description.
With this type of throttle would be difficult to know when the output is at "ZERO". To help with this a ZERO indicator has been added to the next drawing. The indicator can also show the trains direction.
The above schematic shows the addition of a "Zero Indicating" circuit to the throttle. When the output voltage is between +0.7 and -0.7 Volts both of the LED's, D3/4 will be OFF. As the output voltage increases, either PLUS or MINUS, one of the LED's will turn ON.
This will allow the operator to know when the throttle's output voltage is near ZERO and the train is safely stopped.
As there are two LED's, they can also show the direction of travel based on the polarity of the output voltage.
A two colour LED could be used for D3/4. This will give a GREEN indication for one direction and a RED indication for the other.
The next schematic shows an optional "ZERO" indication method. In this case the LED will be ON when the throttles output is near ZERO.
In Option "B" the single LED would be ON when the output voltage is between +0.7 and -0.7 Volts.
The next schematic shows a full featured Toy Throttle Upgrade. This version has Zero Indication, and Momentum.
The transformer and bridge rectifier have been omitted to make the drawing smaller.
All of the features in this circuit can be found in conventional throttle designs. The only difference here is the PLUS or MINUS output voltage capability.
The schematics and text on this page are not highly detailed and some electronics knowledge will be helpful for understanding the detailed functioning of some sections of the circuits. Information on certain sections of the circuits can be found on other pages at this web site. Construction details are left up to the user.
Some of the schematics are in an unusual form as they run vertically rather than on the horizontal. While unconventional this was done as a test to see if this would be more presentable when viewed on web browsers. The drawings should fit on a 8.5 x 11inch sheet of paper when printed.
The explanations for the circuits on these pages cannot hope to cover every situation on every layout. For this reason be prepared to do some experimenting to get the results you want. This is especially true of circuits such as the "Across Track Infrared Detection" circuits and any other circuit that relies on other than direct electronic inputs, such as switches.
If you use any of these circuit ideas, ask your parts supplier for a copy of the manufacturers data sheets for any components that you have not used before. These sheets contain a wealth of data and circuit design information that no electronic or print article could approach and will save time and perhaps damage to the components themselves. These data sheets can often be found on the web site of the device manufacturers.
Although the circuits are functional the pages are not meant to be full descriptions of each circuit but rather as guides for adapting them for use by others. If you have any questions or comments please send them to the email address on the Circuit Index page.